Evidence Coverage & Missing-Evidence Detection
How Estimatics shows how complete each area's documentation is, with a Complete / Partial / Missing signal per dimension, and where else to look for gaps before the file leaves your hands.
5 min read
The most expensive gap in a file is the one you don't notice until someone else does. Estimatics tracks how complete your documentation is, area by area, and shows you where it's thin, so you can fix it while you're still on the property.
Available on every plan, to every role.
The completeness signal on each area
In "Analyze" → "Areas", every area card shows a row of colored dots. Each dot is one dimension of that area's documentation. Hover over a dot to see its name and state.
Open the area to see the full checklist: click "Completeness" in the dossier to expand it. Each dimension shows its state and a short note.
| State | Dot | Note | What it means |
|---|---|---|---|
| "Complete" | Green | "Complete" | This part is documented and confirmed |
| "Partial" | Amber | "Partial — review suggested" | It's there, but something is still a guess or unconfirmed |
| "Missing" | Red | "Action needed" | A real gap. Fix it before you build the estimate or submit |
| "Not evaluated" | Hollow | "Not applicable" | This dimension doesn't apply to this area |
An area with three dashed dots hasn't been evaluated yet ("Completeness not evaluated yet").
The dimensions
Interior rooms are checked on all nine. Roof, elevation and exterior areas use the same list, with fewer items treated as must-haves. "General" areas are checked only on Identity, Damages and Review.
| Dimension | Green when | Red when |
|---|---|---|
| Identity | The area has a real room name | The name is generic ("Other", "General", "Room") or not recognized |
| Measurements | Floor area, perimeter and ceiling height are all known | Any of them is missing (on roof, elevation and exterior areas this shows amber instead) |
| Surfaces | Every surface material is set and confirmed (interior rooms only) | A surface material is missing |
| Damages | The area has damage and all of it is confirmed | Close-up damage photos exist but no damage has been recorded yet |
| Loss context | Water Category and Class (water losses) or Mold Condition (mold) are set and confirmed | They're needed and not set |
| Review | The area is approved | It hasn't been analyzed yet |
| Inventory | The area's elements have been detected | — |
| Element condition | At least one element is marked damaged or to replace | — |
| Additional factors | A few extra questions about the area are all answered | — |
Today, Additional factors stays amber on most areas: there's no screen where you can answer those questions, so you can ignore it.
Amber usually means "there, but not confirmed": a surface the AI presumed, damage still in draft, an area analyzed but not approved. Most amber turns green when you review the area and click "Approve area".
Why "200 photos" isn't the answer
Volume isn't coverage. Two hundred photos of the same wall still leave the ceiling undocumented. The signal is about whether the right evidence and details exist for each area, not how many images you took. It's the difference between a full memory card and a file that holds up.
Other places to spot gaps
- Photos without an area. The Areas board warns "N photos aren't assigned to an area yet — assign them from the Capture tab so they count as evidence."
- The Inspection Guide in Capture tracks the inspection's checklist and coverage. On iPhone, the capture screen shows its percentage in a progress bar while you shoot.
- "Inspection Completeness" on iPhone: in "Analyze", expand the card to see which required items are captured and which are still missing.
- Esti's "Job Context" panel shows the job's "Coverage" %. Ask Esti "What's missing to close this inspection?" (SCOPE and CERTIFY).
- "What's missing" in Estimate lists what the estimate still needs.
→ Files and the Inspection Guide · Esti · Validation and what's missing
Using it in the field
- Work the red dimensions first. Those are the gaps most likely to be questioned.
- Fix the cause: take the missing photos, link measurements, set the surface, declare the damage, fill in the loss context.
- Re-check amber areas before you leave, and approve the ones you've reviewed.
- Treat green as "looks complete", then spot-check anything high-value.
The whole point is timing. It's cheap to fix a gap while you're standing in the room, and expensive to explain one weeks later. Build the file for the review that happens later.
AI Damage Detection — How Findings Work
How findings are proposed, reviewed and confirmed.
Areas and approval
The area dossier, measurements, surfaces and loss context.
Measurements
Where an area's floor, perimeter and ceiling numbers come from.
Evidence-linked estimation
How estimate lines trace back to the findings behind them.
Last updated: October 2026 · Questions? Email support@aiestimatics.com
Last updated: October 2026 · Feedback on this article