The Catalog & Line-Item Matching

How to find the right catalog item by describing the work, how activities like Remove & Replace and Detach & Reset change the price, when to use a custom line, and how AI lines are matched to the catalog.

4 min read


Every priced line in your estimate points to an item in the Estimatics catalog. The item supplies the description, the unit, and the price, so the same work reads and prices the same way on every job. You don't need to memorize codes: you describe the work and pick the item.

Adding and editing lines works on every plan, for Super Admin and Estimator.


Catalog lines vs. custom lines

  • Catalog lines are standardized. The description and unit come from the catalog, and the unit price resolves from the catalog for the item and activity you chose. On a catalog line, the description isn't editable.
  • Custom lines are for work the catalog doesn't cover. You write the "Description", set the unit, and enter the price yourself. Describe the work the way you'd want a reviewer to read it.

Finding the right item

  1. Click "Add Line Item". You're on "Step 1 of 2 · Pick item".
  2. Describe the work in plain words in "Search the work…".
  3. Narrow the list by group, by "Trade", or with "Common work", a short list of frequent items.
  4. Pick an item. If it has options, choose them until only one item matches ("Resolving…"). If options are still missing you'll see "Missing facets — N combinations still match. Pick more to narrow it down."
  5. Click "Add to estimate", then complete "Step 2 of 2 · Configure" and "Save Line".

No luck? "No items match this search." means nothing matched your words. Try different words, or choose "Custom line".

On a line you're adding, "Change item" takes you back to the picker. To swap the item on a line you already saved, remove it and add the right one.


Activities

The activity tells the catalog what work is done to the material, and the price follows it:

ActivityMeaning
"Remove & Replace""Tear out the damaged material and install new."
"Replace""Install new material — no tear-out billed."
"Remove""Tear-out only — nothing installed back."
"Detach & Reset""Take it off, store it, put it back." Then choose "Detach & Reset" or "Reset only".

When the item allows it, you can also split the billing: "Full", "Material only" or "Install only".

Only the activities that item actually prices are offered. A greyed-out option means the item has no price for that activity. "This item cannot be priced at [activity]." means the same thing: pick another activity or another item.


Xactimate codes

Each catalog item maps to an Xactimate code, shown under the item when you configure the line. In the lines table, the "Xactimate codes" switch (in "Columns") shows the Xactimate codes in place of the Estimatics codes.

Xactimate is a trademark of its respective owner. Estimatics is an independent product and is not affiliated with, sponsored, or endorsed by it.


How AI lines are matched

When you use "Build with AI", each confirmed damage is matched to catalog items using a library of standard repair recipes, and the catalog sets the price. Estimatics doesn't invent codes or prices of its own.

Some loss types aren't covered yet. For those, "Build with AI" comes back without lines ("This loss type is not supported yet") and you add the lines by hand. If you see "Recipe library unavailable", it's a system configuration problem, not your job: email support.

→ Build with AI


When to trust the match, and when to look closer

  • A matched item is a strong default, not a verdict. Confirm it describes the actual work.
  • Check the activity. "Remove & Replace" and "Replace" price very differently.
  • For unusual or specialty work, a well-written custom line beats forcing an item that almost fits.
  • After you save, the validation chip flags problems like duplicate lines or the wrong unit. See Validation and what's missing.


Last updated: October 2026 · Questions? Email support@aiestimatics.com

Last updated: October 2026 · Feedback on this article